User Tools

Site Tools


mdcpickandplace:diytray

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
mdcpickandplace:diytray [2010/10/12 00:56]
ladyada created
mdcpickandplace:diytray [2016/01/28 18:05] (current)
Line 1: Line 1:
-<iframe src="​http://​player.vimeo.com/​video/​15752459"​ width="​400"​ height="​225"​ frameborder="​0"​></​iframe><​p><​a href="​http://​vimeo.com/​15752459">​This old pick and place - making a tray</​a>​ from <a href="​http://​vimeo.com/​adafruit">​adafruit industries</​a>​ on <a href="​http://​vimeo.com">​Vimeo</​a>​.</​p>​ +{{ vimeo>​15752459 ​}}
  
 ---- ----
Line 7: Line 6:
  
  
-   +  ​* [[http://​www.mcmaster.com/#​5537T104 | 20mm Extrusion 2 ft piece]] (McMaster #5537T104) x **2 pieces** ​ 
-  * Flange Button Head Cap Screw, M5 Size, 8 mm Length, 0.80 mm Pitch (McMaster #92137A412) x **1 bag** +  * [[http://​www.mcmaster.com/#​5537T154|20mm Extrusion T-nuts]] (McMaster #5537T154) x **4 bags of 4** 
-  * 20mm Extrusion 90 Degree Bracket, Single, 2-Hole (McMaster #537T181) x **4 pieces** +  * [[http://​www.mcmaster.com/#​92137A412|Flange Button Head Cap Screw, M5 Size, 8 mm Length, 0.80 mm Pitch]] (McMaster #92137A412) x **1 bag** 
-  * 20mm Extrusion endcap (Mcmaster #537T14) x **4 pieces** +  * [[http://​www.mcmaster.com/#​5537T181|20mm Extrusion 90 Degree Bracket, Single, 2-Hole]] (McMaster #537T181) x **4 pieces** 
-  * 20mm Extrusion 2' piece (McMaster ​#5537T104) x **2 pieces** +  * [[http://​www.mcmaster.com/#​5537T14|20mm Extrusion endcap]] (Mcmaster #537T14) x **4 pieces** 
-  ​* ​20mm Extrusion ​T-nuts ​(McMaster #5537T154) x **4 bags of 4**+  * [[http://​www.mcmaster.com/#​8560K172&​sesnextrep=343409141868956|Clear Cast Acrylic Sheet, .060" Thick, 12" X 24"​]] ​(Mcmaster ​#8560K172) x **1 piece**  
 + 
 +Total is $50 
 + 
 +====== Quick instructions ====== 
 + 
 +Cut the 20mm extrusion into ~18" pieces (make them a little shorter than the pick and place drawer. 
 + 
 +Attach the pieces with L-brackets so that the L-brackets face each other on the inside of the holder and the outside right edge is flush with the drawer. Keep the left side loose for later adjustment 
 + 
 +Cut two rails from 1/16" material with 5mm drill holes so that the top edge doesnt rise above the JEDEC tray thickness 
 + 
 +Attach the rails with T-slot nuts.  
 + 
 +Place the tray on the holder, slide the left side in and tighten.
/home/ladyada/public_html/wiki/data/attic/mdcpickandplace/diytray.1286844960.txt.gz · Last modified: 2016/01/28 18:05 (external edit)