This shows you the differences between two versions of the page.
Next revision | Previous revision | ||
tutorials:products:bonebox [2012/01/28 05:06] pburgess created |
tutorials:products:bonebox [2016/01/28 18:05] (current) |
||
---|---|---|---|
Line 5: | Line 5: | ||
There's plenty of space inside to add on one of our Beagle Bone Proto Capes with components or connectors soldered on. Fits any Beagle Bone version out there - but not BeagleBoards! | There's plenty of space inside to add on one of our Beagle Bone Proto Capes with components or connectors soldered on. Fits any Beagle Bone version out there - but not BeagleBoards! | ||
- | ===== Parts List ===== | + | ====== Parts List ====== |
The kit includes the following items: | The kit includes the following items: | ||
Line 14: | Line 14: | ||
* Four (4) 3/16" nylon spacers. | * Four (4) 3/16" nylon spacers. | ||
- | + | {{ :tutorials:products:bonebox:parts.jpg?nolink& |}} | |
- | (pic) | + | |
Not included with the kit, you will also need: | Not included with the kit, you will also need: | ||
Line 23: | Line 22: | ||
* Optional: tape. | * Optional: tape. | ||
- | ===== Preparation ===== | + | {{ :tutorials:products:bonebox:optional.jpg?nolink& |}} |
- | * Peel backing paper off the acrylic parts. | + | ====== Preparation ====== |
+ | |||
+ | * Peel the backing paper off the acrylic parts. | ||
* Remove Proto Cape, if installed. | * Remove Proto Cape, if installed. | ||
* Remove microSD card. | * Remove microSD card. | ||
- | ===== Assembly ===== | + | ====== Assembly ====== |
+ | |||
+ | === 1: Attach BeagleBone to Base Plate === | ||
+ | |||
+ | * Insert 4 screws into the BeagleBone's corner mounting holes: | ||
+ | |||
+ | {{ :tutorials:products:bonebox:boardscrews.jpg?nolink& |}} | ||
+ | |||
+ | * Flip the board over, using fingers and thumb to hold the screws in place. If this is a dexterity challenge, the screws can also be held with tape: | ||
+ | |||
+ | {{ :tutorials:products:bonebox:dexterity.jpg?nolink& |}} | ||
+ | |||
+ | * Slide a nylon spacer over each of the four screws. **VERY IMPORTANT: Use ONLY the standoffs included with the kit. DO NOT use wider standoffs in their place, and SUPER ESPECIALLY DO NOT use nuts as a makeshift standoff. The component clearances on the BeagleBone are //very// close, and using the wrong standoffs could result in components being sheared off the board!** | ||
+ | * Slide the base plate over the screws, coming to rest on the spacers. There's a specific orientation for the base plate: one of the four alignment studs is smaller than the others — this should be positioned closest to the USB client port. | ||
+ | * Install four nuts and gently tighten each screw. | ||
+ | |||
+ | {{ :tutorials:products:bonebox:basenuts.jpg?nolink& |}} | ||
+ | |||
+ | * You can now reinstall the proto cape, if using one. | ||
+ | |||
+ | === 2: Assemble Case Sides === | ||
+ | |||
+ | * The case is held together using "T-slot" construction. Holding one of the side pieces, insert a nut into the cross part of the "T" (tape can again provide a temporary hold if needed). | ||
+ | |||
+ | {{ :tutorials:products:bonebox:tslot.jpg?nolink& |}} | ||
+ | |||
+ | * Position one of the end pieces over the alignment studs, then insert a screw through the corresponding hole for the nut. Tighten with gentle finger pressure for now. | ||
+ | |||
+ | {{ :tutorials:products:bonebox:tscrew.jpg?nolink& |}} | ||
+ | |||
+ | * Install the second side piece using the same technique, then repeat with the opposite end face plate, making sure the "up" orientation is the same. It's okay if the box isn't perfectly square at this stage. | ||
+ | |||
+ | {{ :tutorials:products:bonebox:sides.jpg?nolink& |}} | ||
+ | |||
+ | === 3: Install Board in Case === | ||
+ | |||
+ | * Loosen, but //do not completely remove,// the two screws on the **front face** plate. The tip of the screw should be flush with the face of the nut. The face plate can then pivot with just enough clearance for the alignment studs: | ||
+ | |||
+ | {{ :tutorials:products:bonebox:facepivot.jpg?nolink& |}} | ||
+ | |||
+ | * Insert the BeagleBone base plate into the case by inserting the alignment studs into the back face, then pivot the board into place and press the front face flush. | ||
- | ==== A: Attach BeagleBone to Base Plate ==== | + | {{ :tutorials:products:bonebox:pivoting.jpg?nolink& |}} |
- | - Hold 4 screws in place | + | * Now tip the face plate in the opposite direction and install the case top in a similar fashion. Align the hole in the top face with the reset button on the BeagleBone (once sealed, this is accessed with a paper clip or small screwdriver). Or you can choose to keep the top cover off, if you'll need frequent access to the BeagleBone or cape. |
- | - Place nylon spacers over screws | + | |
- | - Slide base plate over screws, with specific orientation | + | |
- | - Install four nuts | + | |
- | - Can install proto cape at this point | + | |
- | ==== B: Assemble Case Sides ==== | + | {{ :tutorials:products:bonebox:resethole.jpg?nolink& |}} |
- | - T-slot construction. Hold side piece, insert screw. | + | * Press the front face flush again and tighten all the screws. Acrylic is brittle, so don't crank these down too hard – finger pressure plus 1/8 turn is sufficient. Insert the microSD card (make sure it goes into the card slot, NOT loose in the case!). Bingo…you're done! |
- | - Position face place in alignment studs. Insert screw, finger tighten. | + | |
- | - Install second side. | + | |
- | - Repeat with opposite face plate, keeping "up" alignment the same. | + | |
- | ==== C: Install Board in Case ==== | + | ====== Access ====== |
- | - Loosen screws on FRONT face plate. | + | To access the board or cape later, it's not necessary to rewind this entire process — most of the parts can be left in place! Just loosen the front case screws 1/8", tip the front face back and pivot the case upward: |
- | - Insert base plate using alignment studs. | + | |
- | - Pivot board into place. | + | |
- | - Tip front face plate the other way, install top cover similarly. Align hole with reset button on board. The top cover can optionally be left off if you'll need frequent access to the board. | + | |
- | - Tighten screws | + | |
- | Can access board by loosening the front case screws 1/8" and pivoting the case up and back. | + | {{ :tutorials:products:bonebox:fliptop.jpg?nolink& |}} |