Differences

This shows you the differences between two versions of the page.

--- wavebubble:wave_bubble_2010 [2010/09/13 17:12]
mictronics
+++ wavebubble:wave_bubble_2010 [2016/01/28 18:05] (current)
@@ Line 5: / Line 5: @@
 This wiki has been created to collect all errata regarding new parts, schematics, etc.
 ==== Wave Bubble 2010 - Design by Mictronics ====
+See this thread for ongoing discussion: [[http://forums.adafruit.com/viewtopic.php?f=16&t=14782]]\\
 === USB and Battery Charger board ===
-Here is a short descrition of the USB and Battery Charger board for my Wave Bubble 2010.\\
+Here is a short description of the USB and Battery Charger board for my Wave Bubble 2010.\\
 Due to hardly available parts on Digikey the battery charging circuit was modified and uses now an LTC1730-4.2
@@ Line 29: / Line 32: @@
 \\
 == Download Design Files ==
-Schematic:\\
+Schematic: {{:wavebubble:wb2010-usb_batt_schematic.pdf|}}\\
-{{:wavebubble:wb2010-usb_batt_schematic.pdf|}}\\
 \\
-PCB Layout:\\
+PCB Layout: {{:wavebubble:wave_bubble-usb_batt_ltc1730.zip|}}\\
-{{:wavebubble:wave_bubble-usb_batt_ltc1730.zip|}}\\
+Gerber files (see .Info):
 \\
 Target Viewer - Required to open the PCB layout files:\\
-[[http://www.target-3001.de/target/v14/englisch/tarv14viewer_e.exe]]\\
+[[http://www.target-3001.de/target/v14/english/tarv14viewer_e.exe]]\\
 \\
 Bill of Material:
 ^Name	^Value			^Package		^DIGIKEY ^
-|BAT1	|LiPo 3.7V/1800mAh	|BATTERIE		 |
+|BAT1	|LiPo 3.7V/1800mAh	|BATTERY		 |
-|C1	|100n			|1206		|399-1249-1-ND	|
+|C1	|.10 uF, 50V			|1206		|399-1249-1-ND	|
-|C2	|100n			|1206		|399-1249-1-ND	|
+|C2	|.10 uF, 50V			|1206		|399-1249-1-ND	|
-|C3	|100n			|1206		|399-1249-1-ND	|
+|C3	|.10 uF, 50V			|1206		|399-1249-1-ND	|
-|C4	|100n			|1206		|399-1249-1-ND	|
+|C4	|.10 uF, 50V			|1206		|399-1249-1-ND	|
-|C5	|1u			|1206		|490-1832-1-ND	|
+|C5	|1uF, 25V			|1206		|490-1832-1-ND	|
-|C6	|220u/6.3V		|SMD_R8X5,4_ELKO	|493-2156-1-ND	|
+|C6	|220uF, 6.3V		|SMD_R8X5,4_ELKO	|493-2156-1-ND	|
-|C7	|47u/6.3V		|SMD_R5X5,4_ELKO	|493-2086-1-ND	|
+|C7	|47uF, 6.3V		|SMD_R5X5,4_ELKO	|493-2086-1-ND	|
 |C8	|1u			|1206		|490-1832-1-ND	|
 |C9	|47n			|1206		|399-1246-1-ND	|
@@ Line 64: / Line 66: @@
 \\
 Digikey BOM ID: 15995
+== Errata ==
+Nothing to report so far.
+== Hints & Testing ==
+  * Populating the board should be a big deal, double check the FT232RL for bad soldering.\\
+  * To test the serial connection just short the RX and TX line on the main board connector and send something through your terminal, the characters will be echoed back.\\
+  * To check the LiPo charger connect a current meter between one battery terminal and the board. Depending on the charging level you should see a continuous current, or in trickle charge mode an intermittent current. Heat the temperature sensor in the middle of the board with a soldering iron, charging should stop immediately and continue after short cool down.
 === Wave Bubble Main Board ===
-PCB still in out for manufacturing...
+Board size is 77mmx52mmx10mm\\
+\\
+Top layer (Prototype Rev. 2a):\\
+{{:wavebubble:wb2010_main_top.jpg?640x480}}
+\\
+Bottom layer (Prototype Rev. 2a):\\
+{{:wavebubble:wb2010_main_bottom.jpg?640x480}}
+\\
+== Download Design Files ==
+Schematic (Rev. 2b): {{:wavebubble:wb2010-main_schematic.pdf|}}
+\\
+PCB Layout (Rev. 2b): {{:wavebubble:wave_bubble-main_new_power_switch_v2.zip|}}\\
+Gerber files (see .Info):
+\\
+Target Viewer - Required to open the PCB layout files:\\
+[[http://www.target-3001.de/target/v14/english/tarv14viewer_e.exe]]\\
+\\
+Bill of Material:
+^Count	^Name	^Value			^Package		^DIGIKEY ^
+|1	|C1	|100u/6.3V	|SMD_R6X6_ELKO	|493-2088-1-ND	|
+|19	|C2,C3,C6,C7,C9,C16,C17,C19,C21,C22,C25,C26,C27,C28,C31,C32,C33,C61,C62	|100n	|1206	|399-1249-1-ND	|
+|10	|C4,C5,C8,C14,C15,C34,C35,C42,C45,C64	|1u	|1206	|490-1832-1-ND	|
+|1	|C10	|10n	|1206	|399-1234-1-ND	|
+|1	|C11	|100u/4V	|SMD_R5X6_ELKO	|493-2079-1-ND	|
+|1	|C12	|470p	|1206	|399-1213-1-ND	|
+|1	|C13	|100u/10V	|6032	|495-1528-1-ND	|
+|1	|C18	|22u/35V	|7243	|495-1583-1-ND	|
+|1	|C20	|68u/16V	|6032	|478-1774-1-ND	|
+|4	|C23,C24,C29,C30	|4.7u	|1206	|399-1262-1-ND	|
+|3	|C36,C40,C47	|68p	|0603	|399-1058-1-ND	|
+|8	|C38,C46,C48,C49,C50,C51,C52,C55	|100p	|0603	|399-1061-1-ND	|
+|2	|C41,C44	|1000p	|0603	|399-1082-1-ND	|
+|3	|C43,C53,C54	|22p	|0603	|399-1053-1-ND	|
+|4	|C56,C57,C58,C63	|10n	|0603	|478-1254-1-ND	|
+|1	|C59	|100n	|0603	|490-1524-1-ND	|
+|1	|C60	|1u	|0603	|445-1322-1-ND	|
+|3	|D1,D2,D3	|SS14	|SMA	|SS14CT-ND	|
+|1	|D4	|GREEN	|1206-D	|160-1206-1-ND	|
+|2	|D5,D6	|SMAZ22-13-F	|SMA	|SMAZ22-FDICT-ND	|
+|1	|IC1	|TPS79333	|SOT-23-5	|296-12961-1-ND	|
+|1	|IC2	|LM2731Y	|SOT-23-5	|LM2731YMFCT-ND	|
+|1	|IC3	|LT1173CS8	|SOIC-8	|LT1173CS8#PBF-ND	|
+|1	|IC4	|LT1301CS8	|SOIC-8	|LT1301CS8#PBF-ND	|
+|1	|IC5	|ATMEGA168-10V	|TQFP32	|ATMEGA168-20AU-ND	|
+|1	|IC6	|AD8402ARZ10	|SOIC-14	|AD8402ARZ10-ND	|
+|1	|IC7	|NE555D	|8-SMD-1	|296-6501-1-ND	|
+|2	|IC8,IC9	|LM358D	|SOIC-8	|497-1591-1-ND	|
+|2	|IC10,IC11	|MIC2514	|SOT-23-5	|576-1085-1-ND	|
+|1	|IC12	|MIC2506YM	|SOIC-8	|576-1084-ND	|
+|1	|IC13	|LMX2433	|TSSOP20	|	|
+|1	|IC14	|LP2985AIM5-2.5CT	|SOT23/5	|LP2985AIM5-2.5/NOPBCT-ND	|
+|1	|JP1	|USB/Batt Board	|1X04	|SAM1029-50-ND	|
+|1	|JP2	|ISP	|2X03-90	|SAM1049-50-ND	|
+|2	|JP5,JP6	|SMA J629-ND	|SMA J629-ND	|J629-ND	|
+|1	|L1	|7.3uH	|CDRH6D28 SERIES	|308-1500-1-ND	|
+|2	|L2,L3	|33uH	|CDRH6D28 SERIES	|308-1494-1-ND	|
+|2	|L4,L5	|FERRIT	|1206	|240-2413-1-ND	|
+|1	|L6	|22nH	|0603	|553-1021-1-ND	|
+|1	|L7	|33nH	|0603	|553-1023-1-ND	|
+|1	|R1	|510K	|1206	|P510KFCT-ND	|
+|1	|R2	|330K	|1206	|P330KFCT-ND	|
+|1	|R3	|47K	|1206	|311-47KERCT-ND	|
+|1	|R4	|13K	|1206	|311-13.0KFRCT-ND	|
+|1	|R5	|820K	|1206	|311-820KERCT-ND	|
+|1	|R6	|50K	|1206	|311-49.9KCRCT-ND	|
+|8	|R7,R13,R16,R17,R18,R19,R38,R39	|10K	|1206	|311-10KERCT-ND	|
+|2	|R8,R9	|1K	|1206	|311-1.0KERCT-ND	|
+|1	|R12	|750	|1206	|P750ECT-ND	|
+|1	|R14	|20K	|1206	|311-20KERCT-ND	|
+|1	|R15	|68	|1206	|311-68ERCT-ND	|
+|2	|R20,R21	|30K(47K)	|1206	|P30.0KFCT-ND	|
+|4	|R23,R24,R25,R27	|0	|0603	|311-0.0GRCT-ND	|
+|2	|R28,R29	|1	|1206	|311-1.0ERCT-ND	|
+|2	|R30,R31	|50	|0603	|RHM49.9HCT-ND	|
+|4	|R32,R33,R34,R35	|18	|0603	|RHM18GCT-ND	|
+|2	|R36,R37	|10K	|0603	|RHM10KGCT-ND	|
+|2	|R40,R42	|10	|0603	|RHM10GCT-ND	|
+|1	|R41	|120	|0603	|RHM120GCT-ND	|
+|2	|R43,R45	|22	|0603	|RHM22GCT-ND	|
+|1	|R44	|47	|0603	|RHM47GCT-ND	|
+|1	|R46	|100	|1206	|311-100ERCT-ND	|
+|2	|R47,R48	|100K	|1206	|311-100KERCT-ND	|
+|2	|S1,S2	|Cycle Program, Power ON	|SWITCH TL3330 SERIES	|EG4388CT-ND	|
+|1	|T1	|MMBT3906	|SOT23/3	|568-1742-1-ND	|
+|2	|T2,T3	|GALI-84	|SOT-89	|www.mini-circuits.com	|
+|1	|T4	|FDN302P	|SSOT	|FDN302PCT-ND	|
+|1	|T5	|FDV303N	|SSOT	|FDV303NCT-ND	|
+|1	|VCO1	|ROS-2700-1819	|VCO CK605 ROS SERIES	|www.mini-circuits.com	|
+|1	|VCO2	|ROS-1300	|VCO CK605 ROS SERIES	|www.mini-circuits.com	|
+|1	|X1	|10MHz	|ABMM Crystal	|535-9150-1-ND	|
+\\
+Digikey BOM ID: 22247
-More edits to come.
+== Errata ==
+Rev. 2b
+   * Nothing to report so far.
+== Hints & Testing ==
+Wavebubble2010 Firmware for hardware tests: {{:wavebubble:wb2010_hardware_test.zip|}}\\
+The ZIP contains the sourcecode and a precompiled .hex file for the ATmega168V.\\
+\\
+Flash the .hex file using a AVR programmer of your choice. Set the ATmega168V fuses as shown below.\\
+\\
+Fuses settings for the AVR ATmega168V in AVR-Studio:{{:wavebubble:avr_fusesettings.jpg}}\\
+\\
+To run the tests connect the Wavebubble2010 via USB and open a terminal programm. Set the terminal to 19200Baud 8N1.\\
+Rest should be self explaining. Type characters to run tests from the menu.

AdaWiki

User Tools

Site Tools

Differences

Page Tools