tutorials:learn:powersupply:transformeracdc.html
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
tutorials:learn:powersupply:transformeracdc.html [2010/10/26 01:31] ladyada |
tutorials:learn:powersupply:transformeracdc.html [2010/10/26 01:35] ladyada |
||
|---|---|---|---|
| Line 37: | Line 37: | ||
| {{http://www.ladyada.net/images/parts/1n4001.jpg?350}} | {{http://www.ladyada.net/images/parts/1n4001.jpg?350}} | ||
| - | You'll want to use a [[http://www.ladyada.net/wiki/partfinder/diodes#power_blocking]power diode such as a 1N4001]], they're extremely common and can put up with a lot of abuse. The side with the silver stripe matches the schematic symbol side that the 'arrow' in the diode symbol is pointing to. Thats the only direction that current can flow. The output is then chopped in half so that the voltage only goes positive | + | You'll want to use a [[http://www.ladyada.net/wiki/partfinder/diodes#power_blocking|power diode such as a 1N4001]], they're extremely common and can put up with a lot of abuse. The side with the silver stripe matches the schematic symbol side that the 'arrow' in the diode symbol is pointing to. Thats the only direction that current can flow. The output is then chopped in half so that the voltage only goes positive |
| {{:tutorials:learn:powersupply:halfsch.png?500|}} | {{:tutorials:learn:powersupply:halfsch.png?500|}} | ||
| Line 73: | Line 73: | ||
| So lets say we have a current draw of 50 mA and a maximum ripple voltage of 10mV we are willing to live with. For a half wave rectifier, the capacitor should be **at least** = 0.05 / (60 * 0.01) = 0.085 Farads = **85,000 uF**! This is a **massive** and expensive capacitor. For that reason, its rare to see ripple voltages as low as 10mV. Its more common to see maybe 100mV or ripple and then some other technique to reduce the ripple, such as a linear regulator chip. | So lets say we have a current draw of 50 mA and a maximum ripple voltage of 10mV we are willing to live with. For a half wave rectifier, the capacitor should be **at least** = 0.05 / (60 * 0.01) = 0.085 Farads = **85,000 uF**! This is a **massive** and expensive capacitor. For that reason, its rare to see ripple voltages as low as 10mV. Its more common to see maybe 100mV or ripple and then some other technique to reduce the ripple, such as a linear regulator chip. | ||
| + | |||
| + | You don't have to measure that formula, but you should keep the following in mind: When the current goes **up** and the capacitor stays the same, the ripple goes **up**. If the current goes **up** and you want the ripple the same, the capacitor must also **increase** | ||
| ===== Full wave rectifiers ===== | ===== Full wave rectifiers ===== | ||
| Line 102: | Line 104: | ||
| {{:tutorials:learn:powersupply:xformerpack2_t.jpg|:tutorials:learn:powersupply:xformerpack2.jpg}} | {{:tutorials:learn:powersupply:xformerpack2_t.jpg|:tutorials:learn:powersupply:xformerpack2.jpg}} | ||
| - | Wow so this looks really familiar, right? From let to right, you can see the wires that come into the transformer from the wall plug, the transformer output has two power diodes on it and a big capacitor (2,200uF). You might be a little puzzled at the **two** diodes - shouldn't there be **four** for a full-wave rectifier? It turns out that if you have a special transformer made with a 'center tap' (a wire that goes to the center) you can get away with using only two diodes. So it is a full wave rectifier, just one with a center-tap transformer. | + | Wow so this looks really familiar, right? From let to right, you can see the wires that come into the transformer from the wall plug, the transformer output has two power diodes on it and a big capacitor (2,200uF). You might be a little puzzled at the **two** diodes - shouldn't there be **four** for a full-wave rectifier? It turns out that [[http://en.wikipedia.org/wiki/Full_wave_rectifier#Full-wave_rectification|if you have a special transformer made with a 'center tap' (a wire that goes to the center) you can get away with using only two diodes]]. So it really is a full wave rectifier, just one with a center-tap transformer. |
| These transformer-based plug-packs are **really cheap** to make - like on the order of under $1! | These transformer-based plug-packs are **really cheap** to make - like on the order of under $1! | ||
/home/ladyada/public_html/wiki/data/pages/tutorials/learn/powersupply/transformeracdc.html.txt · Last modified: 2016/01/28 18:05 (external edit)
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
