This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
wavebubble:battery [2007/12/07 15:01] serial |
wavebubble:battery [2016/01/28 18:05] (current) |
||
---|---|---|---|
Line 14: | Line 14: | ||
* If you're not using the USB-port debugging console (say you have a spectrum analyzer or you're making a bunch and reusing one board multiple times or have a ttl-serial converter) then you can leave out the FTDI chip (and USB connector) | * If you're not using the USB-port debugging console (say you have a spectrum analyzer or you're making a bunch and reusing one board multiple times or have a ttl-serial converter) then you can leave out the FTDI chip (and USB connector) | ||
* If you're planning to power from some other source note that since Vin has to be boosted to 5V the voltage input should be 3.5V-5V. | * If you're planning to power from some other source note that since Vin has to be boosted to 5V the voltage input should be 3.5V-5V. | ||
+ | |||
Line 35: | Line 36: | ||
|2K 1/4W resistor in 1206 pkg|R2|LED choke resistor (~1K depending on LED and brightness)|Mouser|1|$0.08|$0.08| | |2K 1/4W resistor in 1206 pkg|R2|LED choke resistor (~1K depending on LED and brightness)|Mouser|1|$0.08|$0.08| | ||
|Total|-|-|-|-|-|$12-$20| | |Total|-|-|-|-|-|$12-$20| | ||
+ | * Can be sampled for free at low quantities | ||
+ | |||
+ | |||
+ | |||
+ | ==== Parts List - AAA Battery Pack ==== | ||
+ | |||
+ | ^Part # & Datasheets^Name^Description^Distributor^Qty^Cost^Total^ | ||
+ | |Batteries|--|3 alkaline AAA Batteries|Anywhere|3|$0.50|$1.50| | ||
+ | |Batteries(alt.)|--|3 NiMH rechargable AAA batteries|Battery Space (for example or Radioshack, etc|3|$1.25|~$3.75| | ||
+ | |12BH431P|--|3 AAA battery holder |Digikey Mouser|1|$0.89|$0.89| | ||
+ | |Hirose UX60-MB-5ST or *Molex 54819-0572|J1|Mini-B USB connector (SMT)|Digikey Mouser Sample|1|$0.96|$0.96| | ||
+ | |FT232RL|IC2|USB/ttl interface chip (optional)|Mouser|1|$4.10|$4.10| | ||
+ | |B45197A1157K409(tantalum) UWT0J221MCL1GB(electrolytic)|C2|Battery filter capacitor (100uF/6.3V minimum)|Digikey Mouser|1|$0.28|$0.28| | ||
+ | |0.1uF 1206 ceramic capacitor|C4-C7|High frequency bypass capacitor (~.1uF 16V minimum)|Mouser|5|$0.08|$0.40| | ||
+ | |Total|--|--|--|--|--|$3-$10| | ||
+ | ==== Assembly ==== | ||
- | under construction | + | |{{wavebubble:1.jpg|}}|Place the PCB in your vise. For this assembly diagram I will use the lithium ion board, the AAA board is easier.| |
+ | |{{wavebubble:2.jpg|}}|Solder in the DC jack and the FTDI chip. Solderpaste is suggested here.| | ||
+ | |{{wavebubble:3.jpg|}}|Solder in the USB jack. You can now test whether this works by plugging it into a computer.| | ||
+ | |{{wavebubble:4.jpg|}}|Solder in the rest of the components, the low power charging circuitry is not necessary. | | ||
+ | |--|If you are using a battery without protection circuitry, attach it. Solder in the battery. The left pad is + and the right pad is -. | |