This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
wavebubble:wave_bubble_2010 [2010/12/21 14:22] mictronics Updated Digikey non-stock parts |
wavebubble:wave_bubble_2010 [2016/01/28 18:05] (current) |
||
---|---|---|---|
Line 32: | Line 32: | ||
\\ | \\ | ||
== Download Design Files == | == Download Design Files == | ||
- | Schematic:\\ | + | Schematic: {{:wavebubble:wb2010-usb_batt_schematic.pdf|}}\\ |
- | {{:wavebubble:wb2010-usb_batt_schematic.pdf|}}\\ | + | |
\\ | \\ | ||
- | PCB Layout:\\ | + | PCB Layout: {{:wavebubble:wave_bubble-usb_batt_ltc1730.zip|}}\\ |
- | {{:wavebubble:wave_bubble-usb_batt_ltc1730.zip|}}\\ | + | Gerber files (see .Info): |
\\ | \\ | ||
Target Viewer - Required to open the PCB layout files:\\ | Target Viewer - Required to open the PCB layout files:\\ | ||
Line 44: | Line 43: | ||
^Name ^Value ^Package ^DIGIKEY ^ | ^Name ^Value ^Package ^DIGIKEY ^ | ||
|BAT1 |LiPo 3.7V/1800mAh |BATTERY | | |BAT1 |LiPo 3.7V/1800mAh |BATTERY | | ||
- | |C1 |100n |1206 |399-1249-1-ND | | + | |C1 |.10 uF, 50V |1206 |399-1249-1-ND | |
- | |C2 |100n |1206 |399-1249-1-ND | | + | |C2 |.10 uF, 50V |1206 |399-1249-1-ND | |
- | |C3 |100n |1206 |399-1249-1-ND | | + | |C3 |.10 uF, 50V |1206 |399-1249-1-ND | |
- | |C4 |100n |1206 |399-1249-1-ND | | + | |C4 |.10 uF, 50V |1206 |399-1249-1-ND | |
- | |C5 |1u |1206 |490-1832-1-ND | | + | |C5 |1uF, 25V |1206 |490-1832-1-ND | |
- | |C6 |220u/6.3V |SMD_R8X5,4_ELKO |493-2156-1-ND | | + | |C6 |220uF, 6.3V |SMD_R8X5,4_ELKO |493-2156-1-ND | |
- | |C7 |47u/6.3V |SMD_R5X5,4_ELKO |493-2086-1-ND | | + | |C7 |47uF, 6.3V |SMD_R5X5,4_ELKO |493-2086-1-ND | |
|C8 |1u |1206 |490-1832-1-ND | | |C8 |1u |1206 |490-1832-1-ND | | ||
|C9 |47n |1206 |399-1246-1-ND | | |C9 |47n |1206 |399-1246-1-ND | | ||
Line 82: | Line 81: | ||
Board size is 77mmx52mmx10mm\\ | Board size is 77mmx52mmx10mm\\ | ||
\\ | \\ | ||
- | Top layer:\\ | + | Top layer (Prototype Rev. 2a):\\ |
+ | {{:wavebubble:wb2010_main_top.jpg?640x480}} | ||
\\ | \\ | ||
- | Bottom layer:\\ | + | Bottom layer (Prototype Rev. 2a):\\ |
+ | {{:wavebubble:wb2010_main_bottom.jpg?640x480}} | ||
\\ | \\ | ||
== Download Design Files == | == Download Design Files == | ||
- | Schematic:\\ | + | Schematic (Rev. 2b): {{:wavebubble:wb2010-main_schematic.pdf|}} |
\\ | \\ | ||
- | PCB Layout:\\ | + | PCB Layout (Rev. 2b): {{:wavebubble:wave_bubble-main_new_power_switch_v2.zip|}}\\ |
+ | Gerber files (see .Info): | ||
\\ | \\ | ||
Target Viewer - Required to open the PCB layout files:\\ | Target Viewer - Required to open the PCB layout files:\\ | ||
Line 127: | Line 129: | ||
|1 |IC12 |MIC2506YM |SOIC-8 |576-1084-ND | | |1 |IC12 |MIC2506YM |SOIC-8 |576-1084-ND | | ||
|1 |IC13 |LMX2433 |TSSOP20 | | | |1 |IC13 |LMX2433 |TSSOP20 | | | ||
- | |1 |IC14 |LP2985AIM5-2.5CT |SOT23/5 |LP2985AIM5-2.5CT-ND | | + | |1 |IC14 |LP2985AIM5-2.5CT |SOT23/5 |LP2985AIM5-2.5/NOPBCT-ND | |
|1 |JP1 |USB/Batt Board |1X04 |SAM1029-50-ND | | |1 |JP1 |USB/Batt Board |1X04 |SAM1029-50-ND | | ||
|1 |JP2 |ISP |2X03-90 |SAM1049-50-ND | | |1 |JP2 |ISP |2X03-90 |SAM1049-50-ND | | ||
Line 156: | Line 158: | ||
|1 |R41 |120 |0603 |RHM120GCT-ND | | |1 |R41 |120 |0603 |RHM120GCT-ND | | ||
|2 |R43,R45 |22 |0603 |RHM22GCT-ND | | |2 |R43,R45 |22 |0603 |RHM22GCT-ND | | ||
- | |1 |R44 |47 |0603 |RHM47GCT.ND | | + | |1 |R44 |47 |0603 |RHM47GCT-ND | |
|1 |R46 |100 |1206 |311-100ERCT-ND | | |1 |R46 |100 |1206 |311-100ERCT-ND | | ||
|2 |R47,R48 |100K |1206 |311-100KERCT-ND | | |2 |R47,R48 |100K |1206 |311-100KERCT-ND | | ||
Line 168: | Line 170: | ||
|1 |X1 |10MHz |ABMM Crystal |535-9150-1-ND | | |1 |X1 |10MHz |ABMM Crystal |535-9150-1-ND | | ||
\\ | \\ | ||
+ | Digikey BOM ID: 22247 | ||
+ | |||
+ | |||
+ | == Errata == | ||
+ | |||
+ | Rev. 2b | ||
+ | * Nothing to report so far. | ||
+ | |||
+ | == Hints & Testing == | ||
+ | |||
+ | Wavebubble2010 Firmware for hardware tests: {{:wavebubble:wb2010_hardware_test.zip|}}\\ | ||
+ | The ZIP contains the sourcecode and a precompiled .hex file for the ATmega168V.\\ | ||
+ | \\ | ||
+ | Flash the .hex file using a AVR programmer of your choice. Set the ATmega168V fuses as shown below.\\ | ||
+ | \\ | ||
+ | Fuses settings for the AVR ATmega168V in AVR-Studio:{{:wavebubble:avr_fusesettings.jpg}}\\ | ||
+ | \\ | ||
+ | To run the tests connect the Wavebubble2010 via USB and open a terminal programm. Set the terminal to 19200Baud 8N1.\\ | ||
+ | Rest should be self explaining. Type characters to run tests from the menu. |