This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
wavebubble:wave_bubble_2010 [2011/01/16 16:32] mictronics |
wavebubble:wave_bubble_2010 [2016/01/28 18:05] (current) |
||
---|---|---|---|
Line 35: | Line 35: | ||
\\ | \\ | ||
PCB Layout: {{:wavebubble:wave_bubble-usb_batt_ltc1730.zip|}}\\ | PCB Layout: {{:wavebubble:wave_bubble-usb_batt_ltc1730.zip|}}\\ | ||
+ | Gerber files (see .Info): | ||
\\ | \\ | ||
Target Viewer - Required to open the PCB layout files:\\ | Target Viewer - Required to open the PCB layout files:\\ | ||
Line 42: | Line 43: | ||
^Name ^Value ^Package ^DIGIKEY ^ | ^Name ^Value ^Package ^DIGIKEY ^ | ||
|BAT1 |LiPo 3.7V/1800mAh |BATTERY | | |BAT1 |LiPo 3.7V/1800mAh |BATTERY | | ||
- | |C1 |100n |1206 |399-1249-1-ND | | + | |C1 |.10 uF, 50V |1206 |399-1249-1-ND | |
- | |C2 |100n |1206 |399-1249-1-ND | | + | |C2 |.10 uF, 50V |1206 |399-1249-1-ND | |
- | |C3 |100n |1206 |399-1249-1-ND | | + | |C3 |.10 uF, 50V |1206 |399-1249-1-ND | |
- | |C4 |100n |1206 |399-1249-1-ND | | + | |C4 |.10 uF, 50V |1206 |399-1249-1-ND | |
- | |C5 |1u |1206 |490-1832-1-ND | | + | |C5 |1uF, 25V |1206 |490-1832-1-ND | |
- | |C6 |220u/6.3V |SMD_R8X5,4_ELKO |493-2156-1-ND | | + | |C6 |220uF, 6.3V |SMD_R8X5,4_ELKO |493-2156-1-ND | |
- | |C7 |47u/6.3V |SMD_R5X5,4_ELKO |493-2086-1-ND | | + | |C7 |47uF, 6.3V |SMD_R5X5,4_ELKO |493-2086-1-ND | |
|C8 |1u |1206 |490-1832-1-ND | | |C8 |1u |1206 |490-1832-1-ND | | ||
|C9 |47n |1206 |399-1246-1-ND | | |C9 |47n |1206 |399-1246-1-ND | | ||
Line 89: | Line 90: | ||
Schematic (Rev. 2b): {{:wavebubble:wb2010-main_schematic.pdf|}} | Schematic (Rev. 2b): {{:wavebubble:wb2010-main_schematic.pdf|}} | ||
\\ | \\ | ||
- | PCB Layout (Rev. 2b): {{:wavebubble:wave_bubble-main_new_power_switch_v2.zip|}} | + | PCB Layout (Rev. 2b): {{:wavebubble:wave_bubble-main_new_power_switch_v2.zip|}}\\ |
+ | Gerber files (see .Info): | ||
\\ | \\ | ||
Target Viewer - Required to open the PCB layout files:\\ | Target Viewer - Required to open the PCB layout files:\\ | ||
Line 178: | Line 180: | ||
== Hints & Testing == | == Hints & Testing == | ||
- | to be done | + | Wavebubble2010 Firmware for hardware tests: {{:wavebubble:wb2010_hardware_test.zip|}}\\ |
+ | The ZIP contains the sourcecode and a precompiled .hex file for the ATmega168V.\\ | ||
+ | \\ | ||
+ | Flash the .hex file using a AVR programmer of your choice. Set the ATmega168V fuses as shown below.\\ | ||
+ | \\ | ||
+ | Fuses settings for the AVR ATmega168V in AVR-Studio:{{:wavebubble:avr_fusesettings.jpg}}\\ | ||
+ | \\ | ||
+ | To run the tests connect the Wavebubble2010 via USB and open a terminal programm. Set the terminal to 19200Baud 8N1.\\ | ||
+ | Rest should be self explaining. Type characters to run tests from the menu. |