| Image | Name |
Description | Datasheet | Qty |
|||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
PCB |
Printed circuit board v1.1 | Adafruit | 1
|
||||||||
 |
IC1 |
3.3V linear voltage regulator, 250mA current |
MCP1700-3302E/TO | 1 |
|||||||
 |
Q1 |
PNP transistor, EBC pinout | PN2907 | 1 | |||||||
 |
IC2 |
3.3v level converter for SD card If you don't have this part, you probably have a v1.0 kit! |
74AHC125 | 1 | |||||||
 |
C1, C2, C3 |
0.1uF ceramic capacitor | Generic | 3 |
|||||||
 |
C4 |
100uF / 6V capacitor | Generic | 1 |
|||||||
 |
LED1 | Red LED Lite-On LTL-1CHE (or any 3mm LED) |
Generic | 1 |
|||||||
 |
LED2 | Green LED |
Generic | 1 |
|||||||
|
R1, R2, R4 |
1/4W 5% 1.0K resistor Brown Black Red Gold |
Generic | 3 |
|||||||
|
R3 |
1/4W 5% 10K resistor Brown, Black, Orange, Gold |
Generic | 1 |
|||||||
 |
SD |
SD/MMC card holder | Tyco 2041021-3 | 1 |
|||||||
 |
EM-406A | 6 pin SMT connector for EM-406A Either Horizontal or Vertical |
1 |
||||||||
 |
RESET | 6mm tactile switch | B3F-1000 | 1 |
|||||||
 |
ICSP | 6-pin ICSP header | Generic | 1 |
|||||||
 |
8 pin female header (1x8) | Generic | 1 |
||||||||
 |
TXJMP | Jumper/shunt | Generic | 1 |
|||||||
 |
36 pin male header (1x36) | Generic | 1
|
| Image | Name |
Description | Datasheet | Qty |
|||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
PCB |
Printed circuit board | Adafruit | 1
|
||||||||
|
IC1 |
3.3V linear voltage regulator, 250mA current |
MCP1700-3302E/TO | 1 |
|||||||
|
Q1 |
PNP transistor, EBC pinout | PN2907 | 1 | |||||||
|
C1, C2, C3 |
0.1uF ceramic capacitor | Generic | 3 |
|||||||
|
C4 |
100uF / 6V capacitor | Generic | 1 |
|||||||
|
LED1 | Red LED Lite-On LTL-1CHE (or any 3mm LED) |
Generic | 1 |
|||||||
|
LED2 | Green LED |
Generic | 1 |
|||||||
 |
D1 |
3.6V Zener diode If you don't have this part, you probably have a v1.1 kit! |
1N5227B | 1 |
|||||||
|
R1, R2, R7, R11 |
1/4W 5% 1.0K resistor Brown Black Red Gold |
Generic | 4 |
|||||||
|
R3, R5, R6, R8 |
1/4W 5% 4.7K resistor yellow purple red If you don't have this part, you probably have a v1.1 kit! |
Generic | 4 |
|||||||
|
R4, R9, R10 |
1/4W 5% 10K resistor Brown, Black, Orange, Gold |
Generic | 3 |
|||||||
|
SD/MMC card holder | Tyco 1734234-1 | 1 |
||||||||
|
EM-406A | 6 pin SMT connector for EM-406A Either Horizontal or Vertical |
1 |
||||||||
|
RESET | 6mm tactile switch | B3F-1000 | 1 |
|||||||
|
ICSP | 6-pin ICSP header | Generic | 1 |
|||||||
|
8 pin female header (1x8) | Generic | 1 |
||||||||
|
TXJMP | Jumper/shunt | Generic | 1 |
|||||||
|
36 pin male header (1x36) | Generic | 1
|
These parts are not included in the kit, but might be necessary if you're planning to attach different GPS modules.
| Image | Name |
Description | Datasheet | Qty |
|---|---|---|---|---|
|
EB-85A | 8 pin SMT connector for EB-85A Either Horizontal or Vertical |
1 |
|
 |
Trimble | 8 pin SMT header for Trimble GPS | ||
| A1035-D | 20 pin SMT header for Tyco A1035-D | |||
 |
BATT | Backup battery holder for GPS modules that do not contain a supercap or battery | Keystone 3000 | 1 |
 |
BATT | 12mm 3V Lithium coin cell for battery backup | CR1220 or CR1216 | 1 |